Bricklaying – How To Build A Brick Wall

Many people have thought of building a brick wall is one of the easiest situations in construction. However, there are certain methods of doing things to ensure that your all is not only aesthetically pleasing but also strong. Of course the best way to guarantee that your wall is going to be of top quality will be to hire a professional bricklayer. However if you fancy having a go it make sense to have a little practice before attempting your main project.

How To Build A Brick WallEven if you are a seasoned home improvement person you still need to understand the full process to ensure that you get top quality results. On this page and can give you a step-by-step guide for you to follow to ensure that everything goes as smoothly as possible.

This might sound silly but common sense prevails when laying brick wall. Obviously the first thing you’re going to do is buy your bricks. So you don’t have masses of leftover breaks try and work out how many you need before you start the project. Work out the width and height of the wall you are going to be laying and take the measurement of a brick and work out how many bricks of benefit into that space.

I recommend you always slightly over order because on occasion you can have broken bricks and the best thing you need is to have the brick from the same batch so they are exactly the same colour. If you go back and buy some more bricks that have been in a kiln at a different time, then the colour variation will stand out.

Step By Step Guide To Building A Brick Wall

Step 1. Before you even think about laying a brick you need to make sure that your foundations are completely in place. After this you need to mark out where each end of the wall be and then using a string line to make a perfect straight line at brick height. Because planning permission is very strict you need to make sure that the wall is going to be built exactly to the width and height that are on the plans. Always place your bricks on the inside of the string line as the string line should represent limitations.

Step 2. In this step we need to prepare your mortar to be used in building a wall. If you only building a small then hiring a concrete mixer is really a waste of money. We should do is find a large piece of old board and them place four good-sized shovels of sand onto the board and cover with one good site shovel of cement. Borrow a little cold in the centre and slowly mix in water until you get a consistency that is smooth and wet but not falling apart.

Step 3. In this step we can start to lay bricks. First of all lay down some of your mortar so that it is between one and 2 cm thick. Spread this along the line of the wall. Now simply place the first brick and then tap it slightly so it sits evenly and is embedded in the mortar. Place a small a of mortar on the side of the brick and then at the next brick and continue along the line. Use a spirit level to keep the line as straight as possible.

Step 4. At the point of the end of the wall which is called the pillar you should place a brick that is side on to your other life. The key to structural strength here is that each line you build up the brick absolutely must be placed in the opposite direction to the one below.

Step 5. This is the part that most people worry about where you reach the pillar but your bricks are to large to line up correctly. What happens here is you need to create some half bricks. It is way to do this is to simply lay the brick on its side and look for the split point. With one spoof strike in the masonry chisel with a club hammer will split the brick evenly every time.

Step 6. One thing to note is as your wall is getting higher you should be using 10 mm thick mortar in between each layer. These is way to work out if you done it right is that if you’re using a standard brick then it should be 75 mm from the top of one to the bottom of the brick below. It is with better to build its slightly higher because it can be hammered down into place to the exact correct height.

Step 7. As a finishing aspects for the beds simply use the rounded edge of a brick jointer to scrape the mortar inside of the joints. These is way to do is to work on horizontal lines first and then onto the verticals. After you finished remove any excess mortar that is stuck on the outside of the bricks. Once the mortar is dried is extremely difficult to remove.

Once you’ve completed your build simply brush over the wall and ensure that there is no excess mortar as remained on the wall or fall off. It is much easier to clean up and is wet rather than waiting until its gone solid.

Hopefully found this article useful. As mentioned before building a wall is not the most difficult task yet getting it right first time means you have to follow each of these steps to address. I would highly recommend to take a quick look at YouTube video to be sure that you understand each step.